Sika® Primer-157 – Two-component primer for asphalt & mastic asphalt Sika® Primer-157 (formerly MSeal P 157) is a high-quality, two-component primer on a polysulphide-epoxy resin basis. It was developed specifically for adhesion promotion for the polysulphide sealants Sikaflex® CR 170 and CR 171 on asphalt and mastic asphalt. Thanks to its film-forming properties, it also offers a sealing protective film. Product advantages: Film-forming and sealing – for reliable protection of the joint flanks Very good adhesion to asphalt and mastic asphalt Optimal penetration behaviour for permanently resilient bonds Compatible with Sikaflex® CR 170 and CR 171 Areas of application: Bonding agent for asphalt surfaces in road and civil engineering Joint pre-treatment on mastic asphalt for bridges, parking decks or industrial areas Technical properties: Product type: two-component polysulphide-epoxy resin primer Colour: transparent Packaging: 1 litre combination pack Flash-off time: approx. 4 hours at 20 °C (tack-free), overwork after 8 hours at the latest Application temperature: 15–25 °C (component & substrate temperature) Substrate preparation: The joint flanks must be load-bearing, clean, dry and free of oils, greases, loose components, paints and separating substances. The surface is wet-cut or ground with diamond tools to achieve a finely grippy texture. Before application, the substrate must be thoroughly cleaned (vacuumed/blown off) and completely dried. Mixing & application: Stir component A thoroughly. Add component B completely and mix homogeneously with a stirrer at approx. 300 rpm for at least 2 minutes. Apply with a roller or brush to prepared substrates – no puddle formation! Before jointing, the primer must be cured tack-free. Cleaning: Cured primer can only be removed mechanically. Clean hands with cleaning wipes or water & industrial hand cleaner – do not use solvents on the skin. Certifications & approvals: Tested with Sikaflex® CR 170 and CR 171 on mastic asphalt DIBt approvals: Z-74.6-166 (Sikaflex® CR 170) / Z-74.6-168 (Sikaflex® CR 171)

Sika® Primer-127 – Two-component epoxy resin primer for steel and galvanised steel Sika® Primer-127 (formerly MSeal P 127) is a high-quality, two-component primer on an epoxy resin basis for optimal adhesion promotion and corrosion protection for steel, galvanised steel and cathodic dip-coated (KTL) surfaces. The primer was developed specifically for use with the polysulphide sealants Sikaflex® CR 170 and CR 171. Product advantages: Two-component primer and corrosion protection in one – ideal for weathered edge areas Excellent adhesion to steel, galvanised steel and KTL coatings Optimal system compatibility with Sikaflex® CR 170 and CR 171 Long-term protection indoors and outdoors Typical areas of application: Primer for KTL-coated steel Bonding agent and corrosion protection on steel, iron, cast iron Pre-treating galvanised steel before jointing with polysulphide sealants Technical properties: Packaging: 1 litre combination pack Colour: red-brown Application: brushing or rolling Can be overworked with sealant: 8–36 hours after application Temperature when mixing: 15–25 °C Mixing ratio: components A + B, mix thoroughly (min. 3 minutes) Substrate preparation: The bonding surfaces must be load-bearing, clean, dry and free of oil, grease, loose components or coatings. For steel substrates, blasting (SA 2 ½ or St 3 per DIN EN ISO 12944-4) is mandatory. Completely remove old coatings of unknown composition. Application notes: Avoid puddle formation Allow to cure tack-free before jointing The primer does not replace the cleaning of the bonding surfaces Increased consumption possible with longer working times Cleaning: Cured primer can only be removed mechanically Clean hands with suitable cleaning wipes or industrial hand cleaner and water – do not use solvents Certifications & approvals: Tested with Sikaflex® CR 170 and CR 171 DIBt approvals: Z-74.6-166 (CR 170), Z-74.6-168 (CR 171) Component in the Sikalastic® 7801 AS system (approval Z-59.31-428)

Sika® Primer-107 – Silane-based one-component primer for non-absorbent substrates Sika® Primer-107 (formerly MSeal P 107) is a high-quality, one-component bonding agent on a silane basis, developed specifically for use on non-absorbent substrates such as stainless steel, non-ferrous metals and polymer concrete. It optimises the adhesion of the Sikaflex® CR 170 and CR 171 joint sealants and ensures a permanent, secure bond indoors and outdoors. Product advantages: Very good adhesion capability on stainless steel, non-ferrous metals and polymer-bound concrete substitute (PRM/PRC) Low viscosity – for easy, quick application One-component – ready for immediate use without mixing Transparent – discreet application Typical areas of application: Adhesion promotion on non-absorbent substrates such as alloyed steel (e.g. stainless steel) Application on polymer concrete (UP resin) or glazed ceramics Usable indoors and outdoors Technical properties: Material temperature: +5 °C to +40 °C Substrate & air temperature: +5 °C to +40 °C Dew point: component temperature at least 3 °C above the dew point Flash-off time: at least 10 minutes at 23 °C / 50% RH Can be overworked with sealant: 10 to a maximum of 30 minutes Packaging & colour: Container: 1 litre (packaging unit: 4 pieces/box) Colour: transparent Certifications & approvals: Tested in the system with Sikaflex® CR 170 / CR 171 General building-authority approvals: Z-74.6-166 (CR 170) & Z-74.6-168 (CR 171) Usable as a system component in Sikalastic® 7801 AS per Z-59.31-428

Foil sausage nozzle, long The extra-long foil sausage nozzle is specially designed to make dispensing sealants from foil sausages easier. With a total length of 150 mm, it reaches hard-to-access places and offers maximum flexibility in application. Product properties: Total length: 150 mm – ideal for reaching hard-to-access places. Special design: Extra-long nozzle for precise work in tight, hard-to-reach areas. Universally usable: Suitable for all common sausage guns. Compatibility: Nozzle for 400/580/600 ml aluminium foil sausages. Material: High-quality workmanship for long-lasting use and reliable performance. Areas of application: Perfect for professional use in the construction industry, workshops or DIY projects. The long nozzle enables the precise, controlled dispensing of sealants, even in hard-to-reach places. Advantages: This nozzle offers an optimal solution for working with sealants in areas that are difficult to access. It ensures clean, efficient application and increases flexibility and precision at work.