Sika® Primer-215 – System primer for Sikaflex Tank N This primer is part of the approved joint sealing system with Sikaflex Tank N. Product description Sika® Primer-215 is a colourless to slightly yellowish solvent-based primer that reacts with moisture to form a film-building layer. This layer acts as a link between substrate and adhesive and was developed specifically for pre-treating bonding surfaces in combination with Sikaflex® adhesives. Areas of application Sika® Primer-215 is used to improve adhesion on many plastics such as GRP, epoxy resins, PVC, ABS and on wood. Due to the wide variety of plastic formulations, preliminary tests with original materials under the relevant production conditions should be carried out. Manufacturer recommendations should be observed before using Sika® Primer-215 on materials prone to stress cracking. Product properties Chemical basis: Solvent-based polyurethane primer Colour: Colourless, slightly yellowish Solids content: 34% Application temperature: 5 to 40 °C Application notes: Brush, felt or foam applicator Consumption: Depends on surface porosity, approx. 50 g/m² Flash-off time: ≥ 15 °C: 30 minutes < 15 °C: 60 minutes At most 24 hours Technical information Important note: Sika® Primer-215 reacts with moisture. To maintain product quality, it is important to reseal the can with the inner plastic lid immediately after each use. After first opening, the primer should be disposed of after about one month with regular use, or after two months if the can is opened rarely. The 30 ml can is for single use only. Primer that has gelled, separated or shows increased viscosity should no longer be used. Do not dilute or mix Sika® Primer-215 with other substances. When used on transparent or translucent substrates such as glass, plastics etc., adequate UV protection for the bonding surface is mandatory. Application notes The bonding surfaces must be clean, dry and free of grease, oil, dust and contamination. Adhesion can be improved before applying the primer with further pre-treatment steps such as sanding, cleaning and activating. Application Application can be carried out with a brush, felt or foam applicator. Apply Sika® Primer-215 evenly and thinly but with full coverage. The optimal application and surface temperature is between 15 °C and 25 °C. Apply the primer only once, ensuring that the single application provides sufficient coverage. Consumption and method of application depend on the nature of the substrates. Close containers tightly immediately after each use. Sika® Primer-215 – for optimal adhesion on plastics and wood, safe and reliable in use.

WASHI TEC – The evolution of washi adhesive tapes WASHI TEC is the innovative evolution of the proven washi adhesive tapes. These tapes are extremely thin and conformable, yet extremely tear-resistant and stable. They can therefore be applied precisely to smooth and lightly textured substrates, which prevents paint bleed and enables extremely sharp paint edges. This series ensures the highest quality is maintained in the professional painting trade. Outstanding properties: Very thin tape made of WASHI-TEC® paper with a high-quality acrylate adhesive No paint bleed – for extremely sharp paint edges Very conformable – adapts perfectly to smooth and lightly rough surfaces Very good adhesion and tear resistance – stays firmly in place UV-resistant – durable and resistant to sunlight Easy to unroll – for simple, convenient application Technical data: Backing material: WASHI-TEC® Goldkrepp® Temperature resistance: up to 120°C Adhesive type: acrylate Tensile strength: 34.00 N/10 mm Adhesion to steel: 1.60 N/10 mm Elongation at break: 6.00% Area of application: indoors & outdoors Indoor use: up to 6 months Outdoor use: up to 3 months With its particularly high bonding power, the pressure-sensitive adhesive bonds optimally with the substrate yet can still be removed easily and without residue. The adhesive used is of the highest quality, as additives and monomers were blended in during polymerisation.

Dough scraper, small – the smoothing tool Our small dough scraper is a versatile smoothing tool made of special plastic, characterised by excellent handling and a wide range of uses. With a size of approx. 25 cm, this tool is ideally suited to the drag technique when jointing. Properties: Smoothing tool made of high-quality special plastic Ergonomic handling for precise work Versatile for a range of applications Ideal for the drag technique when jointing Compact size: approx. 25 cm Discover the efficiency and flexibility of the small dough scraper and optimise your jointing work with a tool developed specifically for precise, comfortable working.

Foil sausage nozzle, long The extra-long foil sausage nozzle is specially designed to make dispensing sealants from foil sausages easier. With a total length of 150 mm, it reaches hard-to-access places and offers maximum flexibility in application. Product properties: Total length: 150 mm – ideal for reaching hard-to-access places. Special design: Extra-long nozzle for precise work in tight, hard-to-reach areas. Universally usable: Suitable for all common sausage guns. Compatibility: Nozzle for 400/580/600 ml aluminium foil sausages. Material: High-quality workmanship for long-lasting use and reliable performance. Areas of application: Perfect for professional use in the construction industry, workshops or DIY projects. The long nozzle enables the precise, controlled dispensing of sealants, even in hard-to-reach places. Advantages: This nozzle offers an optimal solution for working with sealants in areas that are difficult to access. It ensures clean, efficient application and increases flexibility and precision at work.